November 11, 2026 | Jackie Kuehlmann

Standardization Connects Technologies – Mark Andy and CMC Host Successful Workshops in Warsaw

How can color consistency be ensured in prints produced using different technologies while reducing waste, shortening makeready time and increasing production repeatability? The answer lies in properly implemented standardization of the printing process. Its practical application was demonstrated during the “Standardization Connects Technologies. You Print, We Care” workshops, jointly organized by Mark Andy and CMC at the Mark Andy European Technology Center in Warsaw.

The event brought together several dozen representatives of printing companies, including customers of both companies. The program combined expert presentations with live production demonstrations on two Mark Andy presses based on flexographic and digital (hybrid) technology. Participants were able to follow the successive stages of standardization and compare prints produced in different technologies. The meeting was jointly opened by Lukasz Chruslinski, European Sales Manager Mark Andy, and Malgorzata Szczotka, owner of CMC. As emphasized, the two companies operate in the same areas of the market and share similar goals: enabling printers to achieve high print quality and repeatability, optimize processes and reduce production costs.

From Audit to Repeatable Production
The main part of the program was prepared and conducted by experts of CMC, an independent consultancy specializing in color management and standardization & optimization of printing

Color measurements and print analysis in practice – standardization as the base of consistent print quality.

processes. They presented the successive stages of implementing production standards – from audits and assessments of the technical condition of presses, through parameter selection and calibration, to the implementation of control procedures and ongoing verification of print quality.
Particular attention was paid to the G7 Idealliance method, based, among other things, on controlling tonal response and grey balance. It enables bringing different printing processes toward a common color target while taking their technological characteristics into account.
CMC experts emphasized that effective standardization is not limited to routine calibration adjustments in prepress. Its essential part takes place on the production floor, where press stability, appropriate printing parameters, substrate control and adherence to established procedures are of key importance. Only on this basis is it possible to manage color effectively and maintain the achieved quality during repeat runs, while also enabling optimization of the production process – namely, shorter makeready times and reduced waste.
“Standardization does not eliminate differences between technologies. It allows us to measure, describe and control them. Our goal is to establish production conditions in which the results are predictable and repeatable, regardless of a technology used. It impacts not only on print quality, but also shorter makeready times, less waste and improved production profitability,” says Malgorzata Szczotka.

Two Technologies, One Goal
The practical part of the workshops took place on two Mark Andy presses: the flexographic Evolution Series E5 and the hybrid Digital Series HD HighSpeed 1200. In both cases, demonstrations covered press setup and calibration, as well as control of the parameters affecting the final color result.
An important part of the demonstrations was the use of sample label designs submitted by the event participants. It allowed to relate standardization to real production applications rather than exclusively to laboratory test samples.
In the case of flexography, CMC experts drew attention, among other things, to the importance of properly selecting and checking anilox rollers, the stability of ink transfer, halftone dot characteristics and correction curves. In digital printing, they discussed, among other things, control of the amount of ink applied, linearization, ICC profiling and adjustment of press parameters to the specific substrate and production job.
The demonstrations thus showed how a common color target can be pursued despite differences between the technologies. An important part of the workshops consisted of control measurements and comparisons of the resulting prints with a certified proof, allowing their conformity with the adopted reference to be assessed objectively.

Technology Supported by Expertise

Lukasz Chruslinski (Mark Andy) and Malgorzata Szczotka (CMC) welcome participants to the “Standardization Connects Technologies” workshops.

The workshops also provided an opportunity to present the broader technological capabilities of Mark Andy. Lukasz Chruslinski introduced the company’s product portfolio, with particular emphasis on solutions used in modern label and packaging production. The importance of automation, process stability and integration of successive production stages was also emphasized. These elements, combined with appropriate standardization procedures, enable printers to make fuller use of the potential of their existing press equipment.
“Modern technology creates the conditions for achieving high quality and productivity, but proper preparation and control of the entire production process are equally important. This is why we pay such importance to practical education and the exchange of knowledge with experts and customers. We want to demonstrate not only the capabilities of our presses, but above all ways to use them effectively in everyday production,” emphasizes Lukasz Chruslinski.
The program was complemented by a presentation from Andrzej Jablonski, who represents IST Metz in Poland, a company with which Mark Andy recently began cooperation at the global level. He discussed UV and UV LED curing solutions, including the modular swap4cure concept, which allows curing technology to be flexibly adapted to production needs. One of IST’s systems was installed on the Evolution Series E5 press used during the workshops.

Quality Control in Digital Dimension
A separate topic addressed by CMC was the role of color measurements and digital reporting of production results. As a technology partner of X-Rite, the company presented possibilities of using X-Rite’s measurement and software solutions to document color conformity and control the quality of successive print runs.
This approach enables replacing subjective print assessment with measurement data while also building a record of production parameters. Another important element is the ability to link color control with the work of the ink mixing department, ink formulation and the management of leftover inks.
In practice, this means greater predictability of subsequent jobs, faster identification of deviations and reduced material and time losses. Standardization thus becomes not only a quality assurance tool but also an element of managing production economics.
The workshop participants also included representatives of printing companies using Mark Andy presses where CMC had previously carried out standardization projects. Their presence provided additional context for the topics presented, showing that modern printing technologies and independent consulting expertise can effectively support the same production goals.
The event confirmed the importance of a practical approach to standardization, in which advanced technological solutions, expert knowledge and consistent process control serve a common goal: stable, repeatable and profitable printing production.